Amendment status not verified — confirm the current text below against the official source.
Other particulars relevant to the employment of building workers. Signature of Registering Officer with Seal ANNEXURE The registration granted hereinabove is subject to the following conditions, namely: (a) the certificate of registration shall be non-transferable; (b) the number of workmen employed or building workers in the establishment shall not, on any day, exceed the maximum number specified in the certificate of registration. (c) save as provided in these rules, the fees paid for the grant of registration certificate shall be non-refundable; (d) the rates of wages payable to building workers by the employer shall not be less than the rates prescribed under the Maximum Wages Act, 1948 (11 of 1948) for such employment where applicable, and where the rates have been fixed by agreement, settlement or award, not less than the rates so fixed; and 122 The Building and Other Construction Workers‘ (Regulation of Employment and Conditions of Service) Central Rules, 1998 Forms (e) the employer shall comply with the provisions of the Act and the rules made thereunder. FORM III [SEE RULE 25 (2)] REGISTER OF ESTABLISHMENTS Sr. No. Registration No. and date Name and Address location of the establishment registered where a building or other construction work is to be carried on Name of the Employer and his address Nature of building or other construction work (1) (2) (3) (4) (5) Name and permanent address of the establishment Probable date of commencement of work Maximum number of building workers to be employed on any day Probable duration of building or other construction work & probable date of completion Remarks (6) (7) (8) (9) (10) FORM IV [SEE RULES 26(3) AND 239(1)] NOTICE OF COMMENCEMENT/COMPLETION OF BUILDING OR OTHER CONSTRUCTION WORK (1) (i) Name and address (Permanent) of the establishment…………… (ii) Name of the employer and address ……………………. (2) Name and situation of place where the building and other construction is proposed to be carried on. (3) No. and date of Certificate of registration……………… (4) Name and address of the person incharge of the construction work. (5) Address to which the communications relating to building or other construction work may be sent. (6) Nature of work involved and the facilities including plant or machinery provided. (7) the arrangement storage of explosives, if any, to be used in building or other construction work. (8) In case the notice is for commencement of work, the approximate duration of work. I/We herby intimate that the building or other construction work (Name of work) having registration No. ……….dated ………….is likely to commence/is likely to be completed with effect from……………(date)/on …………………(date). Signature of the Employer Forms The Building and Other Construction Workers‘ (Regulation of Employment and Conditions of Service) Central Rules, 1998 123 To, The Inspector, ………………… …………………. FORM V [SEE RULES 56 AND 74(B), SCHEDULE I] CERTIFICATE OF INITIAL AND PERIODICAL TEST AND EXAMINATION OF WINCHES, DERRICKS AND THEIR ACCESSORY GEAR Test Certificate No. …………… (a) In case of construction site, name of the construction site where lifting appliances are fitted/installed/located: Situation and Description of lifting appliances and Gear with distinguishing number or marks (if any), which have been tested, thoroughly examined Angle to the horizontal of derrick boom at which test load applied Test load applied Safe working load at the angle shown in column (2) (1) (2) (3) (4) (Degrees) (Tonnes) (Tonnes) Name and address of public service, association, company, or firm or testing establishment making the test and examination Name and position of the Competent Person of public service, association, company or firm or testing establishment (5) (6) I certify that on the ……………day of ………20…………the lifting appliance shown in column (1) together with its necessary gear was tested in the manner set forth overleaf in my presence; that a careful examination of the said lifting appliances after the test showed that it had withstood the test load without injury or permanent deformation; and that the safe working load of the said lifting appliance and accessory gear is as shown in column (4). Signature of the Competent Person Date …………………………………………… ………. Seal Registration/Authority number of the Competent Person. FORM VI [SEE RULES 56 AND 74(B)] CERTIFICATE OF INITIAL AND PERIODICAL TEST AND EXAMINATION OF CRANES OR HOISTS AND THEIR ACCESSORY GEAR Test Certificate No. …………… (a) Name of the construction site where cranes or hoists are fitted/installed/located: 124 The Building and Other Construction Workers‘ (Regulation of Employment and Conditions of Service) Central Rules, 1998 Forms Situation and Description For jib cranes radius at the test load was applied Test load applied Safe working load for jib cranes at radius shown in column (2) (1) (2) (3) (4) (Metres) (Tonnes) (Tonnes) Name and address of public, service, association, or firm or testing establishment making the test and examination Name and position of the Competent Person of public service, association, company or firm or testing establishment (5) (6) I certify that on the ……………day of …………20…………the above lifting appliances together with its accessory gear was tested in the manner set forth overleaf; that a careful examination of the said lifting appliance and gear after test showed that it had withstood the test load without injury or permanent deformation; and the safe working load of the said lifting appliance and gear is as shown in column (4). Signature of the Competent Person (See Note 3) *Seal Date Registration/Authority number of Competent Person FORM VII [SEE RULES 70 AND 74(B)] CERTIFICATE OF INITIAL AND PERIODICAL TEST AND EXAMINATION OF LOOSE GEARS Test Certificate No. …………… (a) Name of the construction site where loose gears are fitted/installed/located: Distinguishing Number or Mark Description, dimension and material of gear/device Number tested Date of test Test load applied (tonnes) Safe Working load (SWL) (tonnes) (1) (2) (3) (4) (5) (6) Name and address of manufacturer or suppliers Initial test and examination certificate No. and date (only in case of periodical test and examination) Name and address of public service, association, company or firm or testing establishment making the test and examination Name and position of the Competent Person of public service, association, company or firm or testing establishment (7) (8) (9) (10) Forms The Building and Other Construction Workers‘ (Regulation of Employment and Conditions of Service) Central Rules, 1998 125 I certify that on the ……………day of…………… 20…………the above gear was tested and examined in the manner set forth overleaf; that the examination showed the said gear/device withstood the test load without injury or deformation; and that the safe working load of the said gear/device is as shown in Column 6. Signature of the Competent Person *Seal Date Registration/Authority number of the Competent Person FORM VIII [SEE RULES 62 AND 74(B)] CERTIFICATE OF TEST AND EXAMINATION OF WIRE ROPE BEFORE BEING TAKEN INTO USE Test Certificate No. …………… (1) Name and address of maker or supplier. (2) (a) Circumference/diameter of rope (b) Number of strand (c) Number of wires per strand (d) Lay (e) Core (3) Quality of wire (e.g. Best Plough steel) (4) (a) Date of test of sample of rope (b) Load of which sample broke (tonnes) (c) Safe working load of rope (tonnes) (d) Intended use (5) Name and address of public service, association, company or firm or testing establishment making the test and examination (6) Name and position of Competent Person in public service, association, company or firm or testing establishment making the test and examination. I certify that the above particulars are correct, and that the test and examination were carried out by me and no defect affecting its safe working load (SWL) were found. Signature of the Competent Person Seal Date Registration/Authority number of the Competent Person FORM IX [SEE RULES 72 AND 74(B)] CERTIFICATE OF ANNEALING OF LOOSE GEARS Test Certificate No. …………… (a) Name of the construction site where loose gears are fitted/installed/located: Distinguishing Number or Mark Description of gear Number of the certificate of test & examination Number annealed Date of annealing Defects found at careful inspection after annealing (1) (2) (3) (4) (5) (6) 126 The Building and Other Construction Workers‘ (Regulation of Employment and Conditions of Service) Central Rules, 1998 Forms Name and address of public service, association, company or firm or testing establishment carrying out the annealing and inspection Name and position of Competent Person of public service, association, company or firm or testing establishment (5) (6) I certify that on the date shown in column (5) the gear described in columns (1) to (4) was effectually annealed under my supervision that after being so annealed every article was carefully inspected; and that no defects affecting its safe Woking condition were found other than those indicated in column (6). Signature of the Competent Person Seal Date Registration/Authority number of the Competent Person FORM X [SEE RULES 69 AND 73] CERTIFICATE OF ANNUAL THOROUGH EXAMINATION OF LOOSE GEARS EXEMPTED FROM ANNEALING (a) Name of the Construction site where loose gears are fitted/installed/located: Distinguishing number or mark Description of Gear Number of certificate of initial and periodical test and examination Remarks (1) (2) (3) (4) Name and address of public service, association, company or firm or testing establishment making the test and examination Name and position of Competent Person of public service, association, company or firm or testing establishment (5) (6) I certify that on the ……………day of ……………20…………the above gear, described in column (2) was thoroughly examined; and that no defects affecting its safe working condition were found other than those indicated in column (4). Signature of the Competent Person Seal Date Registration/Authority number of the Competent Person FORM XI [SEE RULE 233(C)] CERTIFICATE OF MEDICAL EXAMINATION